
£28.50 – £60.00 ex. VAT - £34.20
Anticorrosive Quick Dry Primer is a single pack priming solution suitable for most metal substrates. Also suitable for pre-treated aluminium and galvanised steel. Anticorrosive Quick Dry Primer gives excellent protection against corrosion. Excellent build levels and can be re-coated in most types of finish.
– Coverage: 5 m² per litre
– Touch Drying Time: 30 mins – 1 hr
– Recoat: 12 hrs
– Hard Drying Time: 24 hrs

BULK ORDERS? CALL 01782 550733 FOR DISCOUNTS!
COLOURS

Red Oxide

Light Grey
Standard Colours |
Slate Grey and Red Oxide
|
Dry Film Appearance |
Flat
|
Spreading Rate |
5-8m2 per litre (spray application), dependent on film thickness (10m2 @ 50mμ)
|
Touch Dry @20°C |
30 minutes - 1 hour
|
Recoating Time @20°C |
Minimum 12 hours
|
Typical Wet-Film Thickness |
100-150μm per coat
|
Typical Dry-Film Thickness |
50-75μm per coat
|
Solids by Volume |
50% (ASTM D2697) ±3%, dependent on colour
|
VOC Information |
430g per litre (from formula to satisfy EU Solvent Emissions Directive)
|
Application Temperature |
10-35°C
|
Application Method |
Ideally spray; roller or brush for small areas
|
Substrates |
Suitably cleaned and dry surfaces
|
Thinners |
Thinning not recommended. For cleaning, use white spirit.
|
Flash Point |
>25°C
|
Pack Size |
5 litre can; 20 litre can; 205 litre barrel
|
Shelf Life |
12 months
|
Anticorrosive Quick Dry Primer Reviews
Weight | N/A |
---|---|
Select Colour | Red Oxide, Light Grey |
Select Size | 5 Litres, 20 Litres |
Related products
Line Marking Paint - A single-pack quick dry high build floor paint which provides very good durability against abrasion and impact along with with protection against solvent, salt and water damage.
Regal Prime & Seal is a single pack quick dry low viscosity penetrating first coat primer. It's designed to soak into the substrate, providing excellent adhesion of subsequent top coats. Using Regal Prime & Seal will reduce any risk off delamination due to poor penetration of heavy top coats. The sealer anchors the topcoats into the floor. Regal Prime & Seal dries with a flat finish and is opaque in colour. - Coverage: 5-10 m² per litre - Touch Drying Time: 2-4 hours - Recoat: 24 hours - Hard Drying Time: 24 hours
Agricultural Oxide - A long oil based protective metal coating, suitable for all types of interior/exterior substrates. It has excellent covering power and can be used on block work, steel sheets, asbestos sheeting as well as wood. It has a good gloss finish, gives protection against weathering and corrosion.
Two Pack Epoxy Floor Paint (Top Coat) - This epoxy floor coating is designed for application to concrete, cement and non ferrous metals. It provides excellent resistance to water, solvents, acids, alkalis and salts and gives superb adhesion to all recommended substrates. Tough finish has long lasting abrasion and impact resistance. Recommended for areas receiving heavy traffic (vehicle/trucks). Following application of the product: Do not park vehicles or place heavy equipment on the floor for a minimum of 48 hours Do not get the floor wet for a minimum of 7 days as this will cause bloom (discolouration) - Coverage: 5-7 m² per litre - Touch Drying Time: 12-16 hrs - Recoat: 24 hrs - Hard Drying Time:48 hrs - Full Cure: 7 days
Antislip Quick Dry Concrete Floor Paint - A single pack quick drying floor coating. Gives good durability and impact resistance. This gives protection against solvent, salt and water damage. Low slip properties due to fine flat aggregated finish. Antislip Quick Dry Concrete Floor Paint is suitable for heavy duty commercial and industrial areas. - Coverage: 5-10 m² per litre - Touch Drying Time: 3-6 hours - Recoat: 24 hours - Hard Drying Time: 48 hours
Quick Dry Garage Floor Paint - A single pack quick dry floor coating, giving good durability against abrasion and impact with protection against solvent, salt and water damage. Quick Dry Garage Floor Paint is easy to apply with a choice of finishes i.e. gloss/semi/matt. Suitable for heavy duty commercial and industrial areas.
Milking Parlour Wall Paint - Designed for it’s resistance to moisture and industrial pollution, and is also extremely resistant to chemicals, acids and alkaline. Parlour paint is ideal for areas kept hygienically clean by jet washing and detergents. This is based on a chlorinated rubber, halogenated hydrocarbon resin, giving a semi-gloss finish. - Coverage: 5m² per litre - Touch Drying Time: 6hrs - Recoat: 24 hrs - Hard Drying Time: 48 hrs
Quick Dry High Build Floor Paint - A single pack quick dry floor coating which provides good durability against abrasion and impact along with with protection against solvent, salt and water damage. Very easy to apply. Suitable for heavy duty commercial and industrial areas.
Two-Pack Epoxy Topcoat Enamel - Designed to be used in conjunction with Regal epoxy primers for application to most metal substrates. This epoxy metal paint has excellent durability and impact resistance. This coating offers protection from solvents, acids, alkalis and salts. - Coverage: 5-10 m² per litre - Touch Drying Time: 12 hrs - Recoat: 24 hrs - Hard Drying Time:48 hrs - Full Cure: 7 days
Clean and Degrease 5L - A heavy duty, low odour degreaser / detergent. Specially formulated for the removal of fats, grease, oils and stubborn deposits from floors, walls, machinery, paintwork and other hard surfaces. Ideal for preparing your floor ready for a first coat. Suggested to be used in the food handling industry, engineering, offices, shops, hotels and many other areas where regular cleaning is required. A biodegradable, low caustic, low odour, non-solvent cleaner. It can also be used as an ongoing maintenance product to remove foot and tyre marks from painted floors.
Quick Drying Gloss Enamel - Enamel Paint - A tough, long lasting, fast drying metal paint with a gloss finish made on a high build alkyd. High impact resistance, compatible with most primers or as a single coat. Can be used for a variety of applications as diverse as machinery paint, skip paint, shipping container paint and tractor paint. - Coverage: 5-10 m² per litre - Touch Drying Time: 3-6 hours - Recoat: 16 hours - Hard Drying Time: 48 hours
Clean n Etch 5L - This product is made for very smooth / power floated floors or dirty floors. Clean N Etch is a highly concentrated blend of non-fuming acidic compounds and cleaning agents, specifically developed to prepare concrete floors prior to applying paints and other protective coatings.
One Coat High Build Steel Enamel - A tough long lasting, fast drying, semi-gloss primer finish made on a high build alkyd resin. Eliminates the need for two coats and cuts the drying time between coat, reducing labour and paint costs. This protects against corrosion and impacts. - Coverage: 5-10 m2 per litre - Touch Drying Time: 3-6 hours - Recoat: 16 hours - Hard Drying Time: 48 hours
Polyurethane Concrete Floor Paint - A single pack high build floor coating giving medium durability against abrasion and impact, with limited protection against solvent, salt and water damage. Polyurethane Concrete Floor Paint is easy to apply with a gloss or semi-gloss finish. Suitable for light commercial and industrial areas.
Plywood Paint / MDF Paint - A tough, long lasting, fast drying gloss finish made on a high build alkyd. High impact resistance, compatible with most primers or as a single coat. - Coverage: 5-10 m² per litre - Touch Drying Time: 3-6 hours - Recoat: 16 hours - Hard Drying Time: 48 hours
One Coat Gloss Paint - A tough long lasting, fast drying, semi-gloss primer finish made on a high build alkyd resin. Eliminates the need for two coats and cuts the drying time between coat, reducing labour and paint costs. This one coat paint protects against corrosion and impacts.