£19.50 ex. VAT - £23.40
Clean n Etch 5L – This product is made for very smooth / power floated floors or dirty floors. Clean N Etch is a highly concentrated blend of non-fuming acidic compounds and cleaning agents, specifically developed to prepare concrete floors prior to applying paints and other protective coatings.
How Clean n Etch Works
Clean n Etch reacts immediately on the concrete surface, attacking any laitance and thereby opening up the surface to give the concrete a texture of fine sand paper. Fine bubbles of foam are produced during the process. Once the bubbles have ceased, etching is complete. The cleaning agents in Etch n Clean then come into play allowing any soil and fine sand disturbed by the etching process to be washed away. If the floor is then thoroughly rinsed with fresh water, there should be no need to apply a neutralising agent, but best to check that the pH is above 6 as bonding problems can occur if the surface retains traces of acid. Normally, neutralised residues can be safely flushed to the drain. The freshly cleaned, etched and dried surface allows paint and other coatings to bond tightly.
Regal Paint® - Floor Paint Manufacturers
Regal Paint® manufactures hard wearing, long lasting, high-performance floor paint for a complete range of applications, both industrial and commercial. Our floor paints are ideally suited for application on warehouse floors, factory floors, commercial garages, MOT centres, showrooms, chemical plants, galleries and much more. Regal Paints are specialist manufacturers of epoxy floor paint, concrete floor paint, quick-drying paint, garage floor paint and more. Please contact us to discuss your requirements or consult our floor coatings FAQ section for more information..
Clean and Degrease 5L - A heavy duty, low odour degreaser / detergent. Specially formulated for the removal of fats, grease, oils and stubborn deposits from floors, walls, machinery, paintwork and other hard surfaces. Ideal for preparing your floor ready for a first coat. Suggested to be used in the food handling industry, engineering, offices, shops, hotels and many other areas where regular cleaning is required. A biodegradable, low caustic, low odour, non-solvent cleaner. It can also be used as an ongoing maintenance product to remove foot and tyre marks from painted floors.
High Build Phosphate Quick Dry Primer is a single pack priming solution suitable for most metal substrates. This metal paint is also suitable for pre-treated aluminium and galvanised steel. High Build Phosphate Quick Dry Primer gives excellent protection against corrosion. Excellent build levels and can be re-coated in most types of finish. - Coverage: 5 m² per litre - Touch Drying Time: 30 mins - 1 hr - Recoat: 12 hrs - Hard Drying Time: 24 hrs
Two-Pack Epoxy Metal Primer - Designed for a wide range of metal substrates, our two pack epoxy primer offers excellent durability and resistance to contact with solvents, acids, alkalis and salts. It’s hardwearing surface gives good protection against corrosion due to it’s phosphate content. Two-Pack Epoxy Metal Primer is suitable for galvanised steel and aluminium. - Coverage: 5-10 m² per litre - Touch Drying Time: 12 hrs - Recoat: 24 hrs - Hard Drying Time: 48 hrs - Full Cure: 7 days
Regal Prime & Seal is a single pack quick dry low viscosity penetrating first coat primer. It's designed to soak into the substrate, providing excellent adhesion of subsequent top coats. Using Regal Prime & Seal will reduce any risk off delamination due to poor penetration of heavy top coats. The sealer anchors the topcoats into the floor. Regal Prime & Seal dries with a flat finish and is opaque in colour. - Coverage: 5-10 m² per litre - Touch Drying Time: 2-4 hours - Recoat: 24 hours - Hard Drying Time: 24 hours
Anticorrosive Quick Dry Primer is a single pack priming solution suitable for most metal substrates. Also suitable for pre-treated aluminium and galvanised steel. Anticorrosive Quick Dry Primer gives excellent protection against corrosion. Excellent build levels and can be re-coated in most types of finish. - Coverage: 5 m² per litre - Touch Drying Time: 30 mins - 1 hr - Recoat: 12 hrs - Hard Drying Time: 24 hrs