From £4.50 ex VAT - £5.40 inc VAT
Pumice aggregate is an extremely light aggregate which has the advantage of being able to mix into the paint prior to application. It is a non-microbead solution to a fine, aggregated finish.
Pumice gives a rough-profiled finish and significantly increase slip resistance.
When using, pour the pumice into the paint and mix thoroughly. After mixing, use the paint immediately. The paint must be applied with a roller to achieve a consistent finish.
Two Pack High Build Epoxy Garage Floor Paint - Designed for application to concrete, cement and non ferrous metals. Excellent resistance to water, solvents, acids, alkalis and salts. Gives superb adhesion to all recommended substrates. Tough finish has long lasting abrasion and impact resistance. Recommended for areas receiving heavy traffic (vehicle/trucks). - Coverage: 5-7 m² per litre - Touch Drying Time: 12-16 hrs - Recoat: 24 hrs - Hard Drying Time: 48 hrs - Full Cure: 7 days
Regal Prime & Seal is a single pack quick dry low viscosity penetrating first coat primer. It's designed to soak into the substrate, providing excellent adhesion of subsequent top coats. Using Regal Prime & Seal will reduce any risk off delamination due to poor penetration of heavy top coats. The sealer anchors the topcoats into the floor. Regal Prime & Seal dries with a flat finish and is opaque in colour. - Coverage: 5-10 m² per litre - Touch Drying Time: 2-4 hours - Recoat: 24 hours - Hard Drying Time: 24 hours
One Coat High Build Steel Enamel - A tough long lasting, fast drying, semi-gloss primer finish made on a high build alkyd resin. Eliminates the need for two coats and cuts the drying time between coat, reducing labour and paint costs. This protects against corrosion and impacts. - Coverage: 5-10 m2 per litre - Touch Drying Time: 3-6 hours - Recoat: 16 hours - Hard Drying Time: 48 hours
Two Pack Epoxy Floor Paint (Top Coat) - This epoxy floor coating is designed for application to concrete, cement and non ferrous metals. It provides excellent resistance to water, solvents, acids, alkalis and salts and gives superb adhesion to all recommended substrates. Tough finish has long lasting abrasion and impact resistance. Recommended for areas receiving heavy traffic (vehicle/trucks). Following application of the product: Do not park vehicles or place heavy equipment on the floor for a minimum of 48 hours Do not get the floor wet for a minimum of 7 days as this will cause bloom (discolouration) - Coverage: 5-7 m² per litre - Touch Drying Time: 12-16 hrs - Recoat: 24 hrs - Hard Drying Time:48 hrs - Full Cure: 7 days
Polyurethane Concrete Floor Paint - A single pack high build floor coating giving medium durability against abrasion and impact, with limited protection against solvent, salt and water damage. Polyurethane Concrete Floor Paint is easy to apply with a gloss or semi-gloss finish. Suitable for light commercial and industrial areas.
Spiked Shoes (SPIKEDSHOES) Nylon Nail Shoes 1 Pair suitable for up to Shoe size 10 Strong webbing with metal buckles to secure 40mm Nail protrudes 30mm from bottom of shoe Ideal for use in walking over flooring adhesive and Resin coatings.
SuperTough Aggregate is an iron-silicate grit. It has good shatter resistance and has a hard, sharp finish to give fantastic grip. To use SuperTough Aggregate on a previously-painted floor, apply a coat of floor paint and then liberally scatter the grit over the surface of the wet paint. Allow the floor to dry for a full 24 hours. Once dry, remove the excess SuperTough Aggregate that hasn’t stuck with a soft brush. Then the paint over the whole surface of the floor again to seal the grit in place on the floor.
Black-Stripe Nylon material is heat-bonded to the nylon core in manufacture. Ideal for painting floors, the nylon core is solvent resistant and the Nylon fabric is virtually fluff-free in use. This makes this type of roller refill ideal for use with epoxy resin floor paint and other solvent based coatings that would pull fluff from or disolve most other roller refills. Available in four sizes: 9", 12", 15" & 18" wide.
Exterior Wood Paint - Exterior Metal Paint - A long oil based decorative gloss finish designed for a wide range of substrates. Ideal for wooden windows/doors, metal fencing/garage doors or concrete walls. This has excellent covering power and provides long lasting weather protection. - Coverage: 5 - 10 m2 per litre - Touch Drying Time: 12hrs - Recoat: 24 hrs - Hard Drying Time: 48 hrs
One Coat Gloss Paint - A tough long lasting, fast drying, semi-gloss primer finish made on a high build alkyd resin. Eliminates the need for two coats and cuts the drying time between coat, reducing labour and paint costs. This one coat paint protects against corrosion and impacts.
Antislip Quick Dry Concrete Floor Paint - A single pack quick drying floor coating. Gives good durability and impact resistance. This gives protection against solvent, salt and water damage. Low slip properties due to fine flat aggregated finish. Antislip Quick Dry Concrete Floor Paint is suitable for heavy duty commercial and industrial areas. - Coverage: 5-10 m² per litre - Touch Drying Time: 3-6 hours - Recoat: 24 hours - Hard Drying Time: 48 hours
Aluminium Quick Dry Enamel with a tough, quick drying finish. A metal paint made with high grade aluminium flake, rather than pigment, which is dissolved in solvent for 24 hours and diluted with urethan alkyd. Heat resistant up to 150 degrees C. Steel-grey in finish. Typically used to refurbish truck wheels. Advisable to spray. Never use a roller with this product.
Regal Clear Finish is a high solids, medium viscosity, Fast physical drying coating. Displaying Very good adhesion , Very good abrasion resistance., Very good alkali and humidity resistance and Excellent hardness.It's tough, hard wearing Acrylic copolymer is blended with a xylene based solvent.