
£26.00 – £68.00 ex. VAT - £31.20
Polyurethane Concrete Floor Paint – A single pack high build floor coating giving medium durability against abrasion and impact, with limited protection against solvent, salt and water damage. Polyurethane Concrete Floor Paint is easy to apply with a gloss or semi-gloss finish. Suitable for light commercial and industrial areas.

BULK ORDERS? CALL 01782 550733 FOR DISCOUNTS!
PRODUCT NAME
Polyurethane Concrete Floor Paint
PRODUCT DATA SHEET
SAFETY DATA SHEET

Standard Colours |
Slate Grey, Light Grey, Brunswick Green, Ford Tractor Blue, Cornflower Blue, Red Oxide, Post Office Red, Caterpillar Yellow, JCB Yellow, Chocolate Brown, Bright Orange, Black, White.
*Other RAL and British Standard colours can be made, dependent on the quantities required.
|
Dry Film Appearance |
Semi-gloss
|
Spreading Rate |
5-7m2 per litre, dependent on film thickness
|
Touch Dry @20°C |
8 hours
|
Recoating Time @20°C |
Minimum 24 hours
|
Typical Wet-Film Thickness |
85-145μm per coat
|
Typical Dry-Film Thickness |
50-100μm per coat
|
Solids by Volume |
55% (ASTM D2697) +/-3%, dependent on colour
|
VOC Information |
430g per litre (from formula to satisfy EU Solvent Emissions Directive)
|
Application Temperature |
10-35°C
|
Application Method |
Brush or roller
|
Substrates |
Suitably cleaned and dry surfaces
|
Thinners |
Thinning not recommended. For cleaning, use white spirit.
|
Flash Point |
+32°C
|
Pack Size |
5 litre can; 20 litre can; 205 litre barrel
|
Shelf Life |
12 months
|
Polyurethane Concrete Floor Paint – Product Description & Recommended Use
- Single-pack, quick-drying, high-build floor paints providing good durability and impact resistance.
- Limited protection against solvents, salt and water damage.
- Available as a gloss or semi-gloss finish in a range of colours specially formulated to provide good aesthetics and safe use.
- Suitable for light to medium-duty commercial and industrial areas.
- Easy to apply by roller and brush and easy to repaint on high-wear areas.
Polyurethane Concrete Floor Paint Reviews
Regal Paint® - Floor Paint Manufacturers
Regal Paint® manufactures hard wearing, long lasting, high-performance floor paint for a complete range of applications, both industrial and commercial. Our floor paints are ideally suited for application on warehouse floors, factory floors, commercial garages, MOT centres, showrooms, chemical plants, galleries and much more. Regal Paints are specialist manufacturers of epoxy floor paint, concrete floor paint, quick-drying paint, garage floor paint and more. Please contact us to discuss your requirements or consult our floor coatings FAQ section for more information..

Weight | N/A |
---|---|
Select Colour | Brunswick Green, Ford Tractor Blue, Cornflower Blue, Red Oxide, Post Office Red, Caterpillar Yellow, JCB Yellow, Chocolate Brown, Bright Orange, Slate Grey, Light Grey, Black, White |
Select Size | 5 Litres, 20 Litres |
Related products
Two Pack Epoxy Floor Paint (Top Coat) - This epoxy floor coating is designed for application to concrete, cement and non ferrous metals. It provides excellent resistance to water, solvents, acids, alkalis and salts and gives superb adhesion to all recommended substrates. Tough finish has long lasting abrasion and impact resistance. Recommended for areas receiving heavy traffic (vehicle/trucks). Following application of the product: Do not park vehicles or place heavy equipment on the floor for a minimum of 48 hours Do not get the floor wet for a minimum of 7 days as this will cause bloom (discolouration) - Coverage: 5-7 m² per litre - Touch Drying Time: 12-16 hrs - Recoat: 24 hrs - Hard Drying Time:48 hrs - Full Cure: 7 days
Milking Parlour Wall Paint - Designed for it’s resistance to moisture and industrial pollution, and is also extremely resistant to chemicals, acids and alkaline. Parlour paint is ideal for areas kept hygienically clean by jet washing and detergents. This is based on a chlorinated rubber, halogenated hydrocarbon resin, giving a semi-gloss finish. - Coverage: 5m² per litre - Touch Drying Time: 6hrs - Recoat: 24 hrs - Hard Drying Time: 48 hrs
Quick Drying Gloss Enamel - Enamel Paint - A tough, long lasting, fast drying metal paint with a gloss finish made on a high build alkyd. High impact resistance, compatible with most primers or as a single coat. Can be used for a variety of applications as diverse as machinery paint, skip paint, shipping container paint and tractor paint. - Coverage: 5-10 m² per litre - Touch Drying Time: 3-6 hours - Recoat: 16 hours - Hard Drying Time: 48 hours
SuperTough Aggregate is an iron-silicate grit. It has good shatter resistance and has a hard, sharp finish to give fantastic grip. To use SuperTough Aggregate on a previously-painted floor, apply a coat of floor paint and then liberally scatter the grit over the surface of the wet paint. Allow the floor to dry for a full 24 hours. Once dry, remove the excess SuperTough Aggregate that hasn’t stuck with a soft brush. Then the paint over the whole surface of the floor again to seal the grit in place on the floor.
Pumice aggregate is an extremely light aggregate which has the advantage of being able to mix into the paint prior to application. It is a non-microbead solution to a fine, aggregated finish. Pumice gives a rough-profiled finish and significantly increase slip resistance. When using, pour the pumice into the paint and mix thoroughly. After mixing, use the paint immediately. The paint must be applied with a roller to achieve a consistent finish.
Painting Essentials Sundries Pack - ideal for applying both single pack garage floor paint and two-pack epoxy floor paint. 3 x 4" brushes 1 x 15" roller frame 2 x 15" roller heads
Regal Prime & Seal is a single pack quick dry low viscosity penetrating first coat primer. It's designed to soak into the substrate, providing excellent adhesion of subsequent top coats. Using Regal Prime & Seal will reduce any risk off delamination due to poor penetration of heavy top coats. The sealer anchors the topcoats into the floor. Regal Prime & Seal dries with a flat finish and is opaque in colour. - Coverage: 5-10 m² per litre - Touch Drying Time: 2-4 hours - Recoat: 24 hours - Hard Drying Time: 24 hours
Two-Pack Epoxy Floor Sealer (Under Coat) - This epoxy floor paint (first coat) is designed to prepare the surface of concrete, cement and non ferrous metals. This gives an ideal base for epoxy topcoat or acts as a seal coat for bare concrete floors. Resistant to water, solvents, acids, alkalis and salts. Tough finish, and has long lasting abrasion and impact resistance. Recommended for areas receiving heavy traffic (vehicle/trucks). Following application of the product: Do not park vehicles or place heavy equipment on the floor for a minimum of 48 hours Do not get the floor wet for a minimum of 7 days as this will cause bloom (discolouration) - Coverage: 5-7 m² per litre - Touch Drying Time: 12-16 hrs - Recoat: 24 hrs - Hard Drying Time: 48 hrs - Full Cure: 7 days
Single Pack Foor Paint Bundle 3 x 20 Litres - The single pack floor paint bundle is aimed at the light industrial and commercial market. The pack includes all the products you will need to go from a bare concrete floor to a dust free, clean , protected and visually appealing floor. the three products in the bundle are formulated to work together, cross linking to for a durable flooring system. Single pack floor paints whilst not as durable as two pack epoxies are extremely easy to apply and are consistently fast drying in all year round temperatures. 3 x 20lts Product: 1x 20lts Regal Prime and Seal 1x 20lts QUICK DRY HIGH BUILD FLOOR PAINT 1x 20Lts Acrylic Based Regal Clear Finish (with Activator)
Plywood Paint / MDF Paint - A tough, long lasting, fast drying gloss finish made on a high build alkyd. High impact resistance, compatible with most primers or as a single coat. - Coverage: 5-10 m² per litre - Touch Drying Time: 3-6 hours - Recoat: 16 hours - Hard Drying Time: 48 hours
One Coat High Build Steel Enamel - A tough long lasting, fast drying, semi-gloss primer finish made on a high build alkyd resin. Eliminates the need for two coats and cuts the drying time between coat, reducing labour and paint costs. This protects against corrosion and impacts. - Coverage: 5-10 m2 per litre - Touch Drying Time: 3-6 hours - Recoat: 16 hours - Hard Drying Time: 48 hours
Anticorrosive Quick Dry Primer is a single pack priming solution suitable for most metal substrates. Also suitable for pre-treated aluminium and galvanised steel. Anticorrosive Quick Dry Primer gives excellent protection against corrosion. Excellent build levels and can be re-coated in most types of finish. - Coverage: 5 m² per litre - Touch Drying Time: 30 mins - 1 hr - Recoat: 12 hrs - Hard Drying Time: 24 hrs
Two Pack High Build Epoxy Garage Floor Paint - Designed for application to concrete, cement and non ferrous metals. Excellent resistance to water, solvents, acids, alkalis and salts. Gives superb adhesion to all recommended substrates. Tough finish has long lasting abrasion and impact resistance. Recommended for areas receiving heavy traffic (vehicle/trucks). - Coverage: 5-7 m² per litre - Touch Drying Time: 12-16 hrs - Recoat: 24 hrs - Hard Drying Time: 48 hrs - Full Cure: 7 days
Two Pack Epoxy Floor Paint Bundle 5 Litres (25-50 sq meters coverage) - The two pack epoxy floor bundle is designed for heavy use commercial industrial areas or on flooring areas that require a low maintenance long lasting finish. The key advantages over a single pack product are greater resistance to impact and abrasion, also a much greater protection from chemical, acid and alkalis spills. A single pack floor paint may require annual maintenance to ensure high wear points don't erode however epoxy coat should last for a number of years. 3 x 5lts Product: 1x 5 lts TWO PACK EPOXY FLOOR SEALER (UNDERCOAT COAT) 1x 5lts TWO PACK EPOXY FLOOR PAINT (TOP COAT) 1x 5Lts Regal Clear Finish
Aluminium Quick Dry Enamel with a tough, quick drying finish. A metal paint made with high grade aluminium flake, rather than pigment, which is dissolved in solvent for 24 hours and diluted with urethan alkyd. Heat resistant up to 150 degrees C. Steel-grey in finish. Typically used to refurbish truck wheels. Advisable to spray. Never use a roller with this product.
Two-Pack Epoxy Metal Primer - Designed for a wide range of metal substrates, our two pack epoxy primer offers excellent durability and resistance to contact with solvents, acids, alkalis and salts. It’s hardwearing surface gives good protection against corrosion due to it’s phosphate content. Two-Pack Epoxy Metal Primer is suitable for galvanised steel and aluminium. - Coverage: 5-10 m² per litre - Touch Drying Time: 12 hrs - Recoat: 24 hrs - Hard Drying Time: 48 hrs - Full Cure: 7 days